Page 1 of 1

Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Fri Jun 09, 2017 2:28 pm
by venerzky
Cisco ASAv 9.7.1 - Active Standby Failover HA

Router and switch are all IOL.


Image

Image

Image

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Wed Jul 05, 2017 7:45 pm
by rancid84
Thanks for the lab.

I just had an issue. I was not able to start the switches (DMZ,Outside and inside). For some reasons, the switch turn back to gray after I click "start node". Routers (which are using the same IOL image) worked fine.

Not sure if somebody had the same issue. I just removed the nodes and added new ones. Thanks again.

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Wed Jul 05, 2017 7:50 pm
by Uldis (UD)
rancid it is IOL lic issue usually.
and after loaded lab be sure you have set boot from exported, and wipe node before start

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Wed Jul 05, 2017 7:59 pm
by rancid84
Uldis (UD) wrote:
Wed Jul 05, 2017 7:50 pm
rancid it is IOL lic issue usually.
and after loaded lab be sure you have set boot from exported, and wipe node before start
Thanks Uldis,
I think I found the issue: The switches are configured with 128mb for Nvram and ram. I changed that to 256 and the three worked fine.

And btw, there's no configuration included on this lab or at least, I don't see it on the export conf section.

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Wed Jul 05, 2017 8:08 pm
by Uldis (UD)
I recommend use 1024M RAM for IOL:)

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Sun Sep 03, 2017 9:31 pm
by KevBonz
I just downloaded this lab but when I console into the VPCS devices I get a blank console window. Also, there are no config files so not sure if that is how it suppose to be.

I just read the post above and realized I have to wipe the devices before I start them but I still don't see any configs to load from export. Please advise.

Thanks!! Great Lab Topology. I am starting CCNA security studies and this will help!!!

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Sun Sep 03, 2017 10:45 pm
by ramindia
KevBonz wrote:
Sun Sep 03, 2017 9:31 pm
I just downloaded this lab but when I console into the VPCS devices I get a blank console window. Also, there are no config files so not sure if that is how it suppose to be.

I just read the post above and realized I have to wipe the devices before I start them but I still don't see any configs to load from export. Please advise.

Thanks!! Great Lab Topology. I am starting CCNA security studies and this will help!!!
VPCS devices - VPCS not store the config, you can configure the IP, since you know the IP range in the network with IP command.

R!

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Mon Sep 04, 2017 11:43 pm
by Uldis (UD)
you can save VPCS config and export it

on VPCS do command:
save

and export cfg
if you want start your vpcs from saved cfg, need wipe node and vpcs will boot from your cfg

Re: Cisco ASAv 9.7.1 - Active Standby Failover HA

Posted: Tue Sep 05, 2017 3:52 am
by KevBonz
Thanks for explaining about the VPCS. I still don't understand though if there are exported cfgs for the other devices or do i need to do the initial configs.

Cisco ASAv 9 7 1 Active Standby Failover HA

Posted: Mon May 21, 2018 9:01 am
by andreysamign
How much would it cost for the Cisco one?