CTS support on cisco L2 switch
Moderator: mike
-
- Posts: 52
- Joined: Sun Dec 23, 2018 9:53 am
CTS support on cisco L2 switch
Hello,
I know that vios-L2 v20180619 has some cts capabilities (at least the commands are there in the cli) , but I don't manage to get it working.
For now this is a very simple test SW1 (Trunk port1) ----------- (Trunk port1) SW2 , but there is now tag added to frames from SW1 to SW2.
I tested with L3 ports instead of L2, same issue.
Finally I tested CSR1000v(so L3 ports), and the tag is properly added.
so the question: is this viosL2 version does really support cts, or is it just cosmetic ?
Any share experience greatly appreciated.
Thanks
I know that vios-L2 v20180619 has some cts capabilities (at least the commands are there in the cli) , but I don't manage to get it working.
For now this is a very simple test SW1 (Trunk port1) ----------- (Trunk port1) SW2 , but there is now tag added to frames from SW1 to SW2.
I tested with L3 ports instead of L2, same issue.
Finally I tested CSR1000v(so L3 ports), and the tag is properly added.
so the question: is this viosL2 version does really support cts, or is it just cosmetic ?
Any share experience greatly appreciated.
Thanks
-
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: CTS support on cisco L2 switch
100% works with this image
i86bi_LinuxL2-AdvEnterpriseK9-M_152_May_2018.bin
i86bi_LinuxL2-AdvEnterpriseK9-M_152_May_2018.bin
-
- Posts: 52
- Joined: Sun Dec 23, 2018 9:53 am
Re: CTS support on cisco L2 switch
Thanks !
-
- Posts: 52
- Joined: Sun Dec 23, 2018 9:53 am
Re: CTS support on cisco L2 switch
Hi,
are you sure that cts inline tagging is working ok on this version ? I believe it is not.
cts is configurable, le switch can exchane cts pac & environment, but for me inline tagging doesn't work on L2 trunks (doesn't work on L3 ports either).
Below the basic config on each trunk port:
interface Ethernet0/0
switchport trunk encapsulation dot1q
switchport mode trunk
cts manual
policy static sgt 2 trusted
are you sure that cts inline tagging is working ok on this version ? I believe it is not.
cts is configurable, le switch can exchane cts pac & environment, but for me inline tagging doesn't work on L2 trunks (doesn't work on L3 ports either).
Below the basic config on each trunk port:
interface Ethernet0/0
switchport trunk encapsulation dot1q
switchport mode trunk
cts manual
policy static sgt 2 trusted
-
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: CTS support on cisco L2 switch
This switch paired with ASA with PAC keys, worked well for me doing Secv5 task on it.
SGT gropus worked proerly on ASA after dot1x host authorization on IOL SW
Probably not all CTS things are supported on this SW...
SGT gropus worked proerly on ASA after dot1x host authorization on IOL SW
Probably not all CTS things are supported on this SW...
-
- Posts: 52
- Joined: Sun Dec 23, 2018 9:53 am
Re: CTS support on cisco L2 switch
Are you using sxp between the sw and asa ?
-
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: CTS support on cisco L2 switch
yes CTS SXP peering IOL SW and ASA 9.1.6
all virtual
atached IOL SW cfg with CTS SXP
all virtual
atached IOL SW cfg with CTS SXP
You do not have the required permissions to view the files attached to this post.
-
- Posts: 52
- Joined: Sun Dec 23, 2018 9:53 am
Re: CTS support on cisco L2 switch
Thank you.