Palo Stuck In Maintenance Mode
Moderator: mike
-
- Posts: 16
- Joined: Wed Jan 09, 2019 8:06 pm
Palo Stuck In Maintenance Mode
My employer purchased a Pro license and running version 5.0.1-106. Each time I boot a Palo Alto device it loads into maintenance mode. I tried running a factory reset from the menu but that doesn't help either. I have tried two different images. I have also tried doubling the node CPU and memory along with other things I found online when searching the issue but no luck.
Palo devices run fine in our old Eve community lab on an older image.
-112 CPUs, 504Gb memory and 2216Gb disk space.
-Installed bare metal on Linux physical server.
-I have verified the image paths are correct and the naming per the guide.
-Ran the permission fix
-Didn't see anything in the logs
Palo devices run fine in our old Eve community lab on an older image.
-112 CPUs, 504Gb memory and 2216Gb disk space.
-Installed bare metal on Linux physical server.
-I have verified the image paths are correct and the naming per the guide.
-Ran the permission fix
-Didn't see anything in the logs
-
- Posts: 5086
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Palo Stuck In Maintenance Mode
update your EVE, now is 5.0.1-129
also Palo template is updated to support 10x and higher versions
also Palo template is updated to support 10x and higher versions
-
- Posts: 16
- Joined: Wed Jan 09, 2019 8:06 pm
Re: Palo Stuck In Maintenance Mode
Ok I will update.Uldis (UD) wrote: ↑Mon Feb 12, 2024 1:02 amupdate your EVE, now is 5.0.1-129
also Palo template is updated to support 10x and higher versions
Last edited by DreamTFK on Mon Feb 12, 2024 4:30 pm, edited 1 time in total.
-
- Posts: 16
- Joined: Wed Jan 09, 2019 8:06 pm
Re: Palo Stuck In Maintenance Mode
I upgraded to the latest as suggested but it still does not boot.
I see lots of setting I change change such as Qemu, CPU and Qemu NIC but that is a lot of possible combinations to test.
I see lots of setting I change change such as Qemu, CPU and Qemu NIC but that is a lot of possible combinations to test.
-
- Posts: 16
- Joined: Wed Jan 09, 2019 8:06 pm
Re: Palo Stuck In Maintenance Mode
Ok so after playing around with it I found that selecting the v10 image and performing a wipe on the node before boot fixed it.
I cannot get the v11 image to work.
I cannot get the v11 image to work.
-
- Posts: 5086
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Palo Stuck In Maintenance Mode
vers 11, has same template as v10, it works
You do not have the required permissions to view the files attached to this post.
-
- Posts: 16
- Joined: Wed Jan 09, 2019 8:06 pm
Re: Palo Stuck In Maintenance Mode
Well it isn't working for me. I spent an hour on it with another engineer and we only got v10 to work with a wipe.
Never had to do any of that in the past so I am not sure what is going on.
Never had to do any of that in the past so I am not sure what is going on.
-
- Posts: 5086
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Palo Stuck In Maintenance Mode
Wipe is mandatory to do, if you had changed settings for node on topology, qemu line or qemu version.
Wipe means clean previous node settings and force it start from scratch with new assigned settings
This atways been in the EVE, if you did changes on already added node on topology
Wipe means clean previous node settings and force it start from scratch with new assigned settings
This atways been in the EVE, if you did changes on already added node on topology
-
- Posts: 16
- Joined: Wed Jan 09, 2019 8:06 pm
Re: Palo Stuck In Maintenance Mode
That's the thing though. This is my very first time in this lab and it was the very first node I placed.
Really would like to figure out how to get v11 working but 10 will do fine for now.
Really would like to figure out how to get v11 working but 10 will do fine for now.