NX9K VPC POC

Any copyright material exchange is strictly forbidden. Any member violate this rule will be banned without warning.

Moderator: mike

ecze
Posts: 473
Joined: Wed Mar 15, 2017 1:54 pm

NX9K VPC POC

Post by ecze » Fri Aug 18, 2017 10:57 pm

Users ask the topology from Twitter...
Screen Shot 2017-08-19 at 00.43.42.png
NXOS-VPC.zip
E.

PS: shut/no shut interface to enable trunks
You do not have the required permissions to view the files attached to this post.

vkukshal03
Posts: 25
Joined: Fri Mar 24, 2017 9:38 am

Re: NX9K VPC POC

Post by vkukshal03 » Sun Aug 20, 2017 8:55 am

Its nice one.... However have you tried HSRP failover in this....... OR do you have any idea does it work ???

Thanks...

ramindia
Posts: 409
Joined: Sun Mar 19, 2017 10:27 pm

Re: NX9K VPC POC

Post by ramindia » Sun Aug 20, 2017 12:44 pm

vkukshal03 wrote:
Sun Aug 20, 2017 8:55 am
Its nice one.... However have you tried HSRP failover in this....... OR do you have any idea does it work ???

Thanks...
I have configured HSRP with NEXUS 9K, basic config.


here is the output

N7K1# show hsrp
Vlan100 - Group 100 (HSRP-V1) (IPv4)
Local state is Standby, priority 100 (Cfged 100)
Forwarding threshold(for vPC), lower: 0 upper: 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.755000 sec(s)
Virtual IP address is 192.168.1.250 (Cfged)
Active router is 192.168.1.252, priority 100 expires in 7.862000 sec(s)
Standby router is local
Authentication text "cisco"
Virtual mac address is 0000.0c07.ac64 (Default MAC)
3 state changes, last state change 1d04h
IP redundancy name is hsrp-Vlan100-100 (default)

N7K2# show hsrp
Vlan100 - Group 100 (HSRP-V1) (IPv4)
Local state is Active, priority 100 (Cfged 100)
Forwarding threshold(for vPC), lower: 0 upper: 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 2.837000 sec(s)
Virtual IP address is 192.168.1.250 (Cfged)
Active router is local
Standby router is 192.168.1.251 , priority 100 expires in 7.611000 sec(s)
Authentication text "cisco"
Virtual mac address is 0000.0c07.ac64 (Default MAC)
2 state changes, last state change 1d04h
IP redundancy name is hsrp-Vlan100-100 (default)

R!

vkukshal03
Posts: 25
Joined: Fri Mar 24, 2017 9:38 am

Re: NX9K VPC POC

Post by vkukshal03 » Tue Aug 22, 2017 9:46 am

Thanks for you reply.....
My question is not about configuration, it was about fail over.. does it work ?
is there any one who tried fail over testing?

ramindia
Posts: 409
Joined: Sun Mar 19, 2017 10:27 pm

Re: NX9K VPC POC

Post by ramindia » Tue Aug 22, 2017 9:23 pm

vkukshal03 wrote:
Tue Aug 22, 2017 9:46 am
Thanks for you reply.....
My question is not about configuration, it was about fail over.. does it work ?
is there any one who tried fail over testing?
it works for me.

R!

rmadupu
Posts: 2
Joined: Fri Aug 25, 2017 8:55 am

Re: NX9K VPC POC

Post by rmadupu » Sat Aug 26, 2017 5:11 pm

Thank you for the lab, has anyone of you tried vxlan in NXOS , is it possible to start with, from theory it appears to be hardware ASIC which does that so just wanted to know if anyone attempted.

-R

komalthecoolk
Posts: 3
Joined: Thu Aug 31, 2017 4:52 am

Re: NX9K VPC POC

Post by komalthecoolk » Thu Aug 31, 2017 5:52 am

According to the release notes, I think from 7.0.3.I6.1 VXLAN is supported even on their VIRL image, which means it should work on the lab. Though I have the official image for this and can somewhat run it on GNS3, I can't seem to connect to NX9K on Eve-NG (newbie here). Does the device boot for very long before I can connect?

yobansal
Posts: 1
Joined: Sat Apr 01, 2017 10:05 am

Re: NX9K VPC POC

Post by yobansal » Tue Sep 05, 2017 3:54 pm

Yes, VXLAN works on NXOS9kv. I have tested in in EVE-NG.
rmadupu wrote:
Sat Aug 26, 2017 5:11 pm
Thank you for the lab, has anyone of you tried vxlan in NXOS , is it possible to start with, from theory it appears to be hardware ASIC which does that so just wanted to know if anyone attempted.

-R

rmadupu
Posts: 2
Joined: Fri Aug 25, 2017 8:55 am

Re: NX9K VPC POC

Post by rmadupu » Fri Sep 22, 2017 10:31 am

Thank you for the response.

asknet
Posts: 2
Joined: Sat Dec 16, 2017 2:17 pm

Re: NX9K VPC POC

Post by asknet » Sat Dec 16, 2017 6:42 pm

Thanks !!! it Worked

Post Reply