NX9K VPC POC
Moderator: mike
-
- Posts: 533
- Joined: Wed Mar 15, 2017 1:54 pm
NX9K VPC POC
Users ask the topology from Twitter...
E.
PS: shut/no shut interface to enable trunks
E.
PS: shut/no shut interface to enable trunks
You do not have the required permissions to view the files attached to this post.
-
- Posts: 25
- Joined: Fri Mar 24, 2017 9:38 am
Re: NX9K VPC POC
Its nice one.... However have you tried HSRP failover in this....... OR do you have any idea does it work ???
Thanks...
Thanks...
-
- Posts: 409
- Joined: Sun Mar 19, 2017 10:27 pm
Re: NX9K VPC POC
I have configured HSRP with NEXUS 9K, basic config.vkukshal03 wrote: ↑Sun Aug 20, 2017 8:55 amIts nice one.... However have you tried HSRP failover in this....... OR do you have any idea does it work ???
Thanks...
here is the output
N7K1# show hsrp
Vlan100 - Group 100 (HSRP-V1) (IPv4)
Local state is Standby, priority 100 (Cfged 100)
Forwarding threshold(for vPC), lower: 0 upper: 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.755000 sec(s)
Virtual IP address is 192.168.1.250 (Cfged)
Active router is 192.168.1.252, priority 100 expires in 7.862000 sec(s)
Standby router is local
Authentication text "cisco"
Virtual mac address is 0000.0c07.ac64 (Default MAC)
3 state changes, last state change 1d04h
IP redundancy name is hsrp-Vlan100-100 (default)
N7K2# show hsrp
Vlan100 - Group 100 (HSRP-V1) (IPv4)
Local state is Active, priority 100 (Cfged 100)
Forwarding threshold(for vPC), lower: 0 upper: 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 2.837000 sec(s)
Virtual IP address is 192.168.1.250 (Cfged)
Active router is local
Standby router is 192.168.1.251 , priority 100 expires in 7.611000 sec(s)
Authentication text "cisco"
Virtual mac address is 0000.0c07.ac64 (Default MAC)
2 state changes, last state change 1d04h
IP redundancy name is hsrp-Vlan100-100 (default)
R!
-
- Posts: 25
- Joined: Fri Mar 24, 2017 9:38 am
Re: NX9K VPC POC
Thanks for you reply.....
My question is not about configuration, it was about fail over.. does it work ?
is there any one who tried fail over testing?
My question is not about configuration, it was about fail over.. does it work ?
is there any one who tried fail over testing?
-
- Posts: 409
- Joined: Sun Mar 19, 2017 10:27 pm
Re: NX9K VPC POC
it works for me.vkukshal03 wrote: ↑Tue Aug 22, 2017 9:46 amThanks for you reply.....
My question is not about configuration, it was about fail over.. does it work ?
is there any one who tried fail over testing?
R!
-
- Posts: 2
- Joined: Fri Aug 25, 2017 8:55 am
Re: NX9K VPC POC
Thank you for the lab, has anyone of you tried vxlan in NXOS , is it possible to start with, from theory it appears to be hardware ASIC which does that so just wanted to know if anyone attempted.
-R
-R
-
- Posts: 3
- Joined: Thu Aug 31, 2017 4:52 am
Re: NX9K VPC POC
According to the release notes, I think from 7.0.3.I6.1 VXLAN is supported even on their VIRL image, which means it should work on the lab. Though I have the official image for this and can somewhat run it on GNS3, I can't seem to connect to NX9K on Eve-NG (newbie here). Does the device boot for very long before I can connect?
-
- Posts: 1
- Joined: Sat Apr 01, 2017 10:05 am